Canada’s largest selection of Composites, Resins, Gelcoats, Epoxies, Silicones, Urethanes, Fiberglass, Carbon Fiber, Abrasives, and Sundries. 1-877-773-7336 |
A high performance epoxy laminating resin designed for demanding structural applications. Wets fabric easily for predictable laminating with minimal drain. Excellent cured properties with exceptional flexural strength. Heat resistance to 200 F without post-cure. Lower toxicity than comparable products. Mix ratio is 100:33 by volume or 100:27 by wei >>
A medium modulus clear epoxy resin. The original Wood Epoxy Saturation Technique. Easy to use in coating applications. Popular for marine use. Used for gluing, filleting, filling and fairing with appropriate fillers. Working time @ 22 C = 9-12 min (205) or 20-25 min (206).
Sizes: 1.2 quart kit, 1.2 gallon kit, 5.2 gallon kit, 62.4 gallon kit.
An exceptionally clear epoxy system. Mostly used as a moisture resistant natural wood finish on wood strip marine craft. Working time @ 22 C = 20-25 min.
Sizes: 1.3 quart kit, 1.3 gallon kit, 5.8 gallon kit.
Low viscosity laminating epoxy resin. Good mechanical properties and wet-out properties. Optimum strength and Tg is achieved by post-curing. Working time @ 22 C = 37 min @ 575 (226) or 77 min (229).
Sizes: 1.3 gallon kit, 5.8 gallon kit.
Low viscosity, low toxicity laminating resin approved by the German Federal Aviation Authority. Excellent mechanical and wet-out properties. Will not spill out from fabric on vertical surfaces. Will maintain mechanical properties up to 210 F if post-cured. Mix ratio is 100:50 by volume and 100:40 by weight. Hardeners 285 and 287 can be blended to o >>
Low viscosity, low toxicity laminating resin approved by the German Federal Aviation Authority. Excellent mechanical and wet-out properties. Will not spill out from fabrics on vertical surfaces. Will maintain mechanical properties up to 190 F if post-cured. Mix ratio is 100:45 by volume or 100:38 by weight. Hardeners can be blended to obtain optimu >>
Low viscosity, low toxicity, heat resistant laminating resin approved by the German Federal Aviation Authority. Exceptional static and dynamic load bearing properties. Will not spill out of fabric on vertical surfaces. Will maintain mechanical properties up to 250-260 F if post-cures. Mix ratio is 100:48 by volume and 100:40 by weight. Availa >>
A System Three clear low viscosity self-leveling epoxy for use as a tough smooth coating for table tops, bar tops, clocks, hatches, floors, small castings and woodwork. Mix ratio is 2:1; hard surface (80 Shore D).
Sizes: 1.45 pint kit, 3 quart kit, 1.5 gallon kit. Working time @ 25 C = 60 min. >>
An easy to use, non blushing, high performance epoxy laminating system from PTW&W. Low viscosity and fast wet out. Outstanding physical properties across the board and very high heat resistance contributes to greater long term stability than similar products. A highly engineered laminating system with modern ingredients which outperforms common >>
An easy to use, non blushing, high performance epoxy laminating system from PTM&W. Low viscosity and fast wet out. Outstanding physical properties across the board and very high heat resistance contributes to greater long term stability than similar products. A highly engineered laminating system. Working time @ 22 C = 58 min (468).
Sizes: 1.3 >>
A room temperature filled epoxy laminating resin designed for the production of durable, stable tools. Fast wet out with optimum filler load for minimum drain on vertical surfaces. Excellent moisture, chemical and impact resistance make this an excellent general purpose epoxy tooling resin. Thanks to wide hardener selection it is a very versatile r >>
A tough, unfilled room temperature epoxy laminating resin, which can be used to provide service up to well over 200 F without a post cure. Fast wet out and good versatility with a variety of fibers. Works well for the production of structural parts which require good stability, durability and heat resistance not given by other room temperature sett >>
An amber, unfilled intermediate high temperature epoxy laminating resin. For service to 325 F. Additives allow it to wet fabric easily for fast, reliable fabrication. For high temp service parts that cannot be post cured in the mold. Economical high temp resin.
Sizes: 10.5 lb kit, 46.5 lb kit, 446 lb kit. >>
A grey aluminum filled intermediate high temperature epoxy laminating resin. Filler content controls cost, while providing tough tools with high tensile and flexural strength. Ideal resin for tooling that requires a free-standing, off model post cure. This allows use of lower cost patterns, and overall savings in a tooling program. Works well for v >>
A high performance, low viscosity infusion epoxy. Special wetting agents allow for fast, even flow and wet out. Low viscosity does not come at the expense of cured physical properties, which exhibit excellent toughness and heat resistance.
Sizes: 11 lb kit, 44 lb kit, 611 lb kit. >>
An unfilled high temperature laminating system that can provide service over 425 F. Designated for demanding, high temp composite applications. Provides easy wet out, and very easy handling during fabrication. Maybe used for unsupported post cure, however will provide maximum stability when cured on a high temperature master. High temp service obta >>
An aluminum filled room temp epoxy casting system with a medium viscosity for easy handling. A versatile, non setting system for tools, fixtures and molds. Extra filler can be easily added for greater economy.
Sizes: 13.3 lb kit, 44.4 lb kit. >>
A very tough, iron filled room temp epoxy casting system. Non-settling low viscosity system for easy handling and low air entrapment and excellent detail reproduction. Low shrinkage and excellent cured toughness. Very high compressive strength.
Sizes: 15.1 lb kit, 55.8 lb kit >>
An aluminum filled, high temperature casting system. A tough system which pours well to reproduce fine details. Used for foundry patterns, vacuum form molds, compression molding dies and autoclave fixtures and spacers.
Sizes: 13.1 lb kit, 60.3 lb kit. >>
A white filled, high performance fire retardant laminating epoxy. Easy, room temp cure epoxy which exhibits self extinguishing characteristics without the usual fire retarding additives. Good cured physical properties and toughness.
Sizes: 10.8 lb kit, 50 lb kit, 536 lb kit. >>
A two component epoxy casting system designed for production of prototype and production parts. Can be used to cast thin walled complex parts that resemble very tough and durable injection molded plastics. High heat resistance with a great ability to accept pigments. Three hardeners available to facilitate a variety of casting sizes. Makes extremel >>
A high temp epoxy infusion resin with low mixed viscosity and excellent flow characteristics. An excellent system for large infused tooling with the ability to be post cured free standing to save production pattern making costs. Excellent long term stability.
Sizes: 48 lb kit, 605 lb kit. >>
Another clear epoxy from System Three that is suitable for structural fiberglass repairs. Developed for surfboard construction. Contains UV stabilizers. Polyester resin and gelcoat will bond to sanded SB-112.
Sizes: 1.5 pint kit, 1.5 gallon kit >>
A very low viscosity water clear tough epoxy resin. The clearest system that we sell. Excellent wetting out properties. No amine blush. Will not spill out of cloth on vertical surfaces. Popular choice for wood strip boat construction. Working time @ 21 C = 60 min.
Sizes: 1.5 pint kit, 1.5 gallon kit. >>
Catalogue, phone, or in the showroom - we're here to help. With over 25 years in the business, we know the importance of interaction in making sure you are happy with your order and the results our products provide. We want your long term business trust, not just a sale. If you have any ideas that would make it easier for you to get what you need at Composites Canada, please let us know.
Call or Email Us: